I use mine all the time. I posted two pictures so you can see what they look like open and folded away.

 

Thanks that answers my question. I'm not getting any younger and getting into my Pro4x is quite a climb. I think my wife would need a ladder[emoji23]

 

Good advertising shot there Stairmaster

 

Here is something that helps a little. Its called a bump step. I bought it because i park against a concrete wall but it does help getting into the bed .

 

Couple more pics

 

I love those because they will protect your bumper, but depending on local laws they could be illegal. In Alberta they would be illegal. You're not allowed to have anything in your hitch receiver unless you're towing.

 

Some US States share the same law��

 

Some US States share the same law��

You can be ticketed in NYC for driving around with a hitch in. I think some areas of NJ are the same.
Both times I was hit the cop just asked if I and the truck were ok, got my info and gave me a number to call for a police report.

 

I am not aware of law against it in Tx. Mine is kinder than the typical knee knocker

 

It's not illegal in Texas. But hitches do come loose occasionally and you can imagine the damage it can do.

 

Thestairmaster: Does the Nissan step snap back into place like the Amp Research Bed Step?
Also... do you drive the Henday East south bound on weekdays? I see white Pro 4x almost every morning on my commute to Sherwood Park =)

 

Thestairmaster: Does the Nissan step snap back into place like the Amp Research Bed Step?
Also... do you drive the Henday East south bound on weekdays? I see white Pro 4x almost every morning on my commute to Sherwood Park =)

https://www.youtube.com/watch?v=SsfxDX5TKZg

Yes the step does snap back into place. And yes I do sometimes drive that road. Not every day, but a fair amount. Wave next time and I'll keep my eyes out for you.

 

Yes, it appears to be the same step.

 

I don't think so...The Titan step has to be pushed forward from the back.

 

Has anyone installed the OEM step? From watching the AMP Research videos, it appears that there's just a couple of bolts that get pulled out to mount the assembly, but they show it for a Dodge and Toyota; not for the Titan. Going to get one, but would like to know what's involved with installation (couldn't find installation instructions online).

 

Best to call up the parts department at your local Nissan dealer and ask them for installation instructions.

 

Hmmmm looks like Nissan must have some agreement with Amp Research to label their bed step as a Nissan OEM product, but Amp can't sell their own version of it. Amp's own site doesn't list their bed step as compatible with the Titans.... http://www.amp-research.com/products/truckaccessories/bedstep/ The step tread pattern is a bit different, but the size & shape of the step and extending hinge looks to be the same.

It was probably a business decision by Amp to secure a guaranteed OEM contract to make X number of bed steps. If I remember correctly, Amp is the the OEM manufacturer for the GM & Ford motorized running boards.

 

Just ordered the OEM from the dealer. We'll see how it goes.

 

OK, I got the kit yesterday (999T7 W4800) and am getting ready to assemble/install it, and hit a small problem: There's an extra part. It appears to be a spacer plate, however nowhere in the documentation is this thing mentioned. Not even included in the parts list.

Dimensions are 3.0" x 1.52" x 0.34". I.D. of holes are 0.5"

Here are some pics of it:

NEWS FLASH: While writing this, I just went out to www.nissan-techinfo.com and did a search and it turns out there's apparently a newer kit than that advertised on their website - which includes this spacer plate. The new kit number is 999T7 W4820. Here's the link to the new installation instructions. It shows the spacer plate (E), as well as the new part number: http://www.nissan-techinfo.com/asistgc_1/USENG/diskdocs/1/V/C/1VC14.PDF

A search for this new part number comes up blank on both nissanusa.com as well as a google search in general.

The old instructions were Rev. 9/17/2015 (999T7 W4800II Rev 9/17/2015). The new instructions are (999T7 W4820II Rev. 5/13/2016). Looks like they shipped me the latest kit - but with the older instructions.

 

OK, I got the kit yesterday (999T7 W4800) and am getting ready to assemble/install it, and hit a small problem: There's an extra part. It appears to be a spacer plate, however nowhere in the documentation is this thing mentioned. Not even included in the parts list.

Dimensions are 3.0" x 1.52" x 0.34". I.D. of holes are 0.5"

...
The old instructions were Rev. 9/17/2015 (999T7 W4800II Rev 9/17/2015). The new instructions are (999T7 W4820II Rev. 5/13/2016). Looks like they shipped me the latest kit - but with the older instructions.

Any chance you still have that spacer? I just installed a kit that didn't have one and it presses up against the bumper. I think I'd rather have a little space.

 

Successfully installed with no problems - other than the bolts being torqued to 101 ft/lbs! Real bitch to get off. I torqued them back on as close as I could get to 101 ft/lbs while lying on my back. The design is very well thought out. They have a plastic retainer clip that holds down a cable run. You pinch that off to remove it, and a bolt from the bracket goes into that hole. The bracket then has another hole right next to it that the plastic retainer clip goes into. MUCH easier getting into the bed of the truck now.

 

I installed mine on Friday and didn't see a need for that spacer. I didn't see it in my instructions either so left it out. The bolts they supplied were the same size as the ones you take off. seems to me they should of been a little longer to make up for the plate. Since it does not hit my bumper without the plate I will just leave it as is. Love the step though

 

If I would of had my pintle in when I got rearended the lady's mini van wouldn't of hit my lower panels.

 

Is the step hitch reversible to install on the passenger side as well? I would like to install one but the door on my camper shell opens to the driver side and the step would be of little assistance then.

 

No. Driver side only.

 

No, sorry. I ended up using it - once I re-read the correct instructions.

 

I made my own spacer with a few large washers and it worked great.

 

Does the step work any good when the tailgate is down? Just got a tool box that sits under my tonneau cover and will need to get into my truck often

 

Yes

 

I use mine all the time. I love it.

 

Step should come standard as you have to have a small ladder if you don't have one.

 

Retract

Are those bumper steps spring loaded? What holds them in the retracted position? What material, aluminum--steel?

 

Are those bumper steps spring loaded? What holds them in the retracted position? What material, aluminum--steel?

Yes, spring-loaded. Don't know the material, but suspect it's aluminum.

 

One to One points

Can Nissan One to One purchase points be used to buy one of these steps. I haven't figured out how to use the points with the Nissan estore internet site.

 

Can Nissan One to One purchase points be used to buy one of these steps. I haven't figured out how to use the points with the Nissan estore internet site.

You'll need to look at your One to One account to see how they allocated those points. In my case, they allocated them to Service only.

 

One to One

OK, I stopped by the dealer today to see if I could buy a rear bumper step for my PR and use One to One points. NOPE, they told me the sales points are only good for a new vehicle purchase. I purchased three new Nissans in the last two years. Not going to buy another in the near future. What good are the points???? Worthless.
I do love my XD though. Great truck. It is NOT a 3/4 ton but it is a great 1/2 ton truck.:nerd2: